Implementing HP Enterprise Virtual Array Solutions : HP0-402 Exam
Product Description
Exam Number/Code: HP0-402
Exam Name: Implementing HP Enterprise Virtual Array Solutions
Questions Type: Multiple choice,
“Implementing HP Enterprise Virtual Array Solutions”, also known as HP0-402 exam, is a HP certification.
Preparing for the HP0-402 exam? Searching HP0-402 Test Questions, HP0-402 Practice Exam, HP0-402 Dumps?
With the complete collection of questions and answers, Pass4sure has assembled to take you through 71 questions to your HP0-402 Exam preparation. In the HP0-402 exam resources, you will cover every field and category in HP AIS helping to ready you for your successful HP Certification.
Questions and Answers : 71 questions
Updated: March 20th , 2008
Question: 1
Using Command View EVA, which attributes are displayed for HSV2×0 Controller Properties. Select THREE.
A. mirror port states
B. temperature sensors
C. UPS voltage indicators
D. cache battery module states
E. levels of protection from shelf failures
Answer: A, B, D Question: 2
What are two capabilities of the HP Command View EVAPerf? Select TWO.
A. review port status
B. creation of vdisks
C. display SAN topology
D. collect host connection data
E. review capacity planning data
Answer: A, D Question: 3
What is the maximum number of disk enclosures for an EVA6000?
A. 4
B. 6
C. 8
D. 18
Answer: C Question: 4
What does the EVA provide in a heterogeneous environment? Select TWO.
A. mainframe support
B. no single point of failure
C. reliable and infinitely scalable
D. modular and scalable storage
E. preconfigured operating system solutions
Answer: B, D Question: 5
A customer requires a six hour call-to-repair commitment. Which minimum type of HP Care Pack
Service is appropriate?
A. HP Support Plus
B. HP Critical Service
C. HP 4 Hour, 24×7 Hardware Support
D. HP Proactive Essentials 24×7 Unlimited
Answer: B
Page 1 of 16
TK
Exam Name: Implementing HP Enterprise Virtual Array Solutions
Exam Type HP
Exam Code: HP0-402 Total Questions: 70
Question: 6
What is the best practice when adding disks to an EVA 2C8D for a Robust Availability
Configuration?
A. After adding the disks, delete and recreate the disk group.
B. Add disks in multiples of eight; distributed evenly across the shelves.
C. Install any number of disks and assign each of them individually to the appropriate redundant storage set.
D. After installing a single disk, wait until leveling has taken place in the existing disk group before you install the next disk.
Answer: B Question: 7
Which methods are available to provide system administrators direct notification of Field
Replaceable Unit (FRU) failures? Select TWO.
A. e-mail
B. RPC traps C. SCMI traps D. SNMP traps E. syslog event
Answer: A, D Question: 8
Which disks are used to optimize price per capacity for your EVA storage subsystem? Select
TWO.
A. higher performance disks
B. near online disks
C. larger capacity disks
D. smaller capacity disks
Answer: B, C Question: 9
Why would you consider configuring two separate disk groups instead of a single one? Select
TWO.
A. higher availability
B. lower cost of ownership
C. higher storage efficiency
D. better database performance
E. better utilization of disk space
Answer: A, D Question: 10
How many FC switched fabric connections are there on each M5314A drive enclosure?
A. 0
B. 2
C. 4
D. 8
Page 2 of 16
TK
Exam Name: Implementing HP Enterprise Virtual Array Solutions
Exam Type HP
Exam Code: HP0-402 Total Questions: 70
Answer: A
Question: 11
How is the drive enclosure address assigned?
A. by the loop switches
B. by the enclosure address bus
C. by the HSV controllers at power up
D. by the order that the drive enclosures are powered up
Answer: B Question: 12
What does the EMU do? Select TWO.
A. powers off HSV controllers
B. monitors disk enclosure temperatures
C. monitors disk enclosure and controller temperature sensors
D. reports disk enclosure events through the Enclosure Address Bus (EAB)
Answer: B, D Question: 13
In an EVA4000, what happens to the remaining disk enclosures when one disk enclosure becomes unavailable?
B. The remaining enclosures shut down to retain data consistency.
C. The HSV controllers reroute the data around the unavailable enclosure.
D. The remaining enclosures reset enclosure addresses to bypass the failed enclosure.
Answer: A
No comments:
Post a Comment